Projecta IP600
600W 12V Intelli-Wave Pure Sine Wave Inverter
Intelli-Wave
The Projecta IP600 converts 12V DC battery power into 240V AC, 50Hz output for running compatible 240V appliances away from mains power. This model provides 600W continuous, 840W surge under 3 minutes, 1200W surge under 3 seconds and uses Pure sine wave output.
Always confirm the appliance power requirement, start-up surge, battery capacity, cable size and installation requirements before use.
Input: 12V DC, 9.75–15.5V; 60A max
Output: 600W continuous, 840W surge under 3 minutes, 1200W surge under 3 seconds
AC output: 240V AC, 50Hz
Waveform / type: Pure sine wave
USB output: Not listed as a main output on the product page
Battery guidance: Minimum 50Ah, ideal 50–130Ah
Fuse / protection: Internal fuse: 110A; recommended external fuse kit IFB-100
Dimensions: 250 x 168 x 81 mm
Weight: 2.2 kg
Warranty: 5 years
Sensitive electronics and general 240V appliances within the inverter rating.
Vehicle, caravan, marine and remote power installations.
Applications requiring a remote display or controlled inverter installation.
Use only a suitable 12V DC battery system.
Battery capacity guidance: Minimum 50Ah, ideal 50–130Ah.
Ensure the battery is fully charged and in good condition before operating high loads.
High-power appliances draw very high DC current. Undersized batteries, cables or fuses can cause voltage drop, shutdown or battery damage.
Runtime guidance: Approx. 30 minutes at 600W on a 30Ah battery; approx. 3 hours at 100W on a 30Ah battery.
Install the unit in a dry, cool and well-ventilated location.
Keep ventilation openings clear and do not mount the unit where heat can build up.
Install the correct fuse or circuit breaker as close as practical to the battery positive terminal.
Use the cable size and installation method specified in the instruction manual.
Check polarity carefully before connecting the DC cables.
Make sure all connected appliances are switched off before turning the inverter on.
Turn the inverter on and allow it to start normally.
Connect or switch on appliances one at a time.
Do not exceed the continuous output rating or peak surge capability.
If a fault occurs, switch the unit off, remove the load, correct the cause and restart the unit.
Confirm the DC battery voltage is within the correct operating range.
Check the DC fuse or circuit breaker and all battery connections.
Confirm the battery is adequately charged and suitable for the load.
Check that the remote control lead is connected correctly if using the remote.
The appliance may exceed the continuous output rating or peak surge rating.
The battery voltage may be dropping below the shutdown threshold.
The cable size, fuse rating or connection quality may be causing voltage drop.
The unit may have entered overload, over-temperature or short-circuit protection.
Yes. Intelli-Wave models produce pure sine wave AC output, which is suitable for sensitive electronics when the load is within the inverter rating.
Read the instruction manual before installation or use.
Use the inverter in a dry, cool and well-ventilated location protected from rain, water, dust and excessive heat.
Do not install the inverter in the same compartment as batteries or flammable materials.
Always use correctly sized DC cables, fuses and secure connections.
Do not connect the AC output to fixed building wiring, mains wiring, or another inverter output unless the manual specifically allows the installation and it is completed by a licensed electrician.
High AC voltage is present during operation. Do not open or service the unit unless qualified.
Reverse polarity connection can damage the inverter and may not be covered under warranty.
The Projecta IP600 is listed with a 5 years warranty under normal use. Warranty does not cover damage caused by incorrect installation, reverse polarity, misuse, modification, overload, water ingress, physical damage or failure to follow the product instructions.
If the issue continues after completing the troubleshooting steps, stop using the inverter and contact Projecta support.
Please provide:
Product model: IP600
Serial number if available
Battery system voltage and battery capacity
Connected appliance type and wattage rating
Photos of the installation, fuse, cable connections and any fault display
Battery voltage reading with no load and while the appliance is connected